Picture
    My backyard has a great little raised garden. I plant broccoli and carrots with the kids, and they snack on lettuce and spinach when they're playing outside. It's the whole reason they love vegetables. If you can grow it, and pick it, it tastes better when you eat it. We really started getting into it, and I realized that a trellis would enable us to grow more of our favorite things, like sugar snap peas, pole beans, and watermelons. Yes, watermelons. We don't have much space for watermelons in our little garden, but I love them so much, I decided to make space. 

    Since my ultimate goal was to trellis watermelons, I knew I was going to need a trellis that would support some weight. My local hardware store sells decorative wood and plastic trellises, but they weren't strong enough, and to build a custom wooden trellis would be pretty expensive. Instead, I opted to build my own trellis from random, inexpensive things found in almost any hardware store: 1/2 inch EMT conduit from the electrical aisle, 1/2 inch galvanized pipe elbows from the plumbing aisle, and a standard garden trellis net from the garden department. 

    First, I cut the EMT to the size I needed, with a hack saw. Make sure that you don't bend the edges of the EMT too far when you cut them, because you'll need them to fit into the plumbing elbows. The trellis in this picture is 5'x5', so I cut two 5' sides, and one 5' top. Next, I wove one piece of EMT through the  side of the net, to hold the net to the side of the trellis, and stuck the bottom of the EMT into the ground to hold it in place. Then I did the same on the other side of the net, to form the other side, and stuck that piece of EMT into the ground about 5' away.     
    

Picture
    After I stuck both sides in the ground, I wove the remaining piece of EMT through the top of the net, and attached the top of the trellis to the sides with galvanized elbows. It was a little bit of a juggling act keeping all of the pieces together while I put the elbows in place, since I only have two arms, but if you have the patience to wait until someone else is around to hold things in place for you before you start a project, it will be really simple.

Picture
    I also made two more trellises so that I could pretty much grow anything anywhere in my garden. These are each 10' wide, by 5' tall. Since these are so wide, I supported them in the middle with an additional piece of EMT, and I held it in place with a 3/4 inch galvanized T in the middle of the 10' top of the trellis.

    These trellises cost about $10 each, so they fit my budget perfectly. I haven't had much success with watermelons yet, but they have been perfect for sugar snap peas and pole beans.
 
Picture
    I have an ugly bathroom. It's under the stairs, so it's awkwardly shaped, and someone painted it a weird color. It's got a pretty little pedestal sink, but that doesn't make up for all of the ugly going on in that little bathroom. It's got a basic, builder grade mirror, so I decided to make it a quick frame. I used some moulding that I found in the garage, some adhesive caulking I had left over from another project, and a little bit of trim paint. It cost me nothing to make, except about 2 hours of my time.

Picture
    First, I measured the mirror and decided how big I wanted the frame to be. Then, I cut the moulding with a mitre (or miter, depending on where you're from) box and saw. This took me about an hour, but if you're better than I am at hinting to your family and friends that you really want a power mitre saw for your birthday, it would only take you a couple of minutes...
    With the moulding cut to size, I glued it together in the shape of a frame with some paintable adhesive caulking. This was actually the most exciting part of the project because the side of the caulking blew out when I put it in the gun. So, instead of pretty little caulking lines, I rubbed globs of caulking from the side of the caulking cartridge onto the edges of the moulding. It wasn't the most graceful, but it worked. 
    

Picture
    After the caulking dried, I painted the frame. I found some door and trim paint in the garage, so the frame matches the rest of the trim in the house. After the two coats of paint dried, I attached some little metal mirror hanging brackets to the back of the frame, so that I can hang it for now, and then remove it when I paint the bathroom. After I paint the bathroom, I'll take off the mirror clips and get a new caulking cartridge to attach it to the mirror.

Picture
    Then, I hung the frame right on top of the mirror. It came out pretty nice, for nothing. I'll go back and permanently attach it to the mirror later, but for now, it looks so much nicer! 
    If you don't have any spare trim or baseboard lying around your garage, you can get the trim for a couple of dollars a foot at Home Depot or Lowes, so it's still much less expensive than the mirror framing kits sold in craft stores. 
    I originally got the idea here. She layered a couple of pieces of trim to create a beautiful effect on a much larger mirror.

 
Picture
    We have a great covered patio in our backyard, but it's really hard to enjoy when the sun is glaring in your eyes. I wanted to get something that could block the sun when I needed it, but would easily store away when I didn't. When I went out to buy some outdoor roll-up blinds, I found that all the ones that were big enough for my patio were crazy expensive. So, I decided to make some myself. 
    I got some shade cloth, 1/2 inch PVC pipe (stay with me, here) and two copper pipe straps. Lowes sells shade cloth for a couple of dollars a linear foot, by about 5 feet wide, in a few differet colors. 
    First, I stitched a hem in the sides of the shade cloth so the edges wouldn't be all ratty, and then I stitched a hem in the top and bottom of the shade cloth, big enough to slide the PVC through.
     Then, I cut the PVC about 2 inches longer than the width of the hemmed shade, so that I would have room to mount the shade with the pipe straps.
    I hung the shade cloth on the PVC, and then put another piece of PVC through the bottom hem so that it wouldn't flap in the wind. You could also use something much thinner for the bottom, like a small wood dowel, but I had a bunch of PVC lying around so I used that (I like PVC a lot.).      

Picture
    After the shade cloth was on the PVC curtainrod, I mounted it to the patio roof with the pipe straps. You could also use a curtain mounting kit, but the pipe straps are only a few cents each, so I went with those.     

Picture
    The shade stays rolled up out of the way when we're not using it, but it's easily rolled out when we need it. I used strap of double sided velcro to hold it in place while it's rolled up, but you could also use a string, or even mount hooks to rest it in. 
    You can see in this picture that the PVC continues past the shade cloth because I ended up using the PVC from the shade cloth for my patio misting system that I put in later. 

    The patio shade cost about $10 to make, and it took about 2 hours, because I stitched the hems by hand, and I'm not exactly a stellar seamstress...

 
Picture
    If you're looking for an easy way to change the look of your bedroom, try making an upholstered headboard. It's very simple to do, and it's inexpensive. Mine took about an hour to make, and cost about $25. All you need is some wood, foam or quilt batting, fabric to cover it with, and a staple gun to hold it all together. 
    First, determine how big you want your headboard to be, Remember, if you are going to hang it on the wall behind the bed, you can measure the space above the bed the you want the headboard to cover. If you are going to attach it to the back of the bedframe, make sure you account for the wood you will need to attach it.
    If you have plywood at your house, just cut it to the size you need. If you don't live in a lumberyard, and don't have a saw to cut your own, Home Depot and Lowes will both cut wood to size. If you're going to purchase the wood, check the scrap section at the hardware store to see if they have any large scraps you can use at a major discount. I got a huge piece of plywood for $3, and the guy even cut it to the exact measurements I needed. 
    Then, choose the fabric you want. Make sure you get enough so that you can pull it around the edges of the wood and staple it to the back. I used an indoor/outdoor fabric because it's easy to wipe down when the kids decide to have a juice fight on my bed, but you can find some really nice upholstry fabric if you're willing to pay for it. Fabric stores also sell upholstry tacks, and buttons, if you're fancy.
    Also, decide whether you want to use foam or quilt batting. I didn't want mine to have the overstuffed look, so I went with quilt batting. If you use foam, make sure you have an adhesive to stick it to the wood. 
     If you want to use upholstry buttons, drill holes in the wood where you're going to put them, so you can anchor them to the back of the headboard. 
    Now, all you have to do is put it all together. If you're using batting, lay out the fabric, front side down, and lay the batting on top of it. Then put the wood on top of the batting, pull the fabric and batting tightly around the edges of the wood, and staple it in place. If you're using foam, use a spray adhesive to attach the foam to the wood. When it's dry lay the fabrich out, front side down, and then put the foam and wood on top of it. Tightly pull the fabric around the edges of the wood, and staple it in place. Add any upholstry tacks and buttons, and then step back and marvel at the piece of art you just created.
    I hung mine on the wall. If you can hang a picture, you can hang a headboard. Or you could also attach it to the back of your bedframe. BOOM. Headboard.

 
Picture
    This is one of my favorite things around our house. It only cost a few dollars to make, and it will never be completely finished, but it's a pretty reminder of how much we love our family, even when we're far apart. 
   First, I got a bunch of little unfinished wooden birdhouses at a craft store. They are only a dollar each, and we used the acrylic paint I already had, so it didn't cost much. Then, I harrassed each member of my extended family into painting one when they came over to our house. We had a big family Christmas Dinner at our house, and then a birdhouse painting party after dinner. It was great to see my kids painting with their great-grandmother. Everyone had their own inspiration, and each birdhouse has a different personality. 
    When the birdhouses were dry, I sprayed them with an outdoor polyurethane to protect them from the weather, and hung them in the apple tree out in the garden. You can always see them peeking out through the leaves, but when the leaves fall, the birdhouses are left to remind us that no matter how far apart we are, we are all part of the same famly tree.